TI-600 POWER AMPLIFIER MODULE

TI-600 POWER AMPLIFIER MODULE
Click to enlarge
Price: $185.00
Product ID : TI-600 Module
Manufacturer: Class D Audio USA
E-mail to a friend | Add To Wish List

Purchase

Description

This audio power amplifier is based on the Texas Instruments TAS5630 digital amplifier chip, a high-performance, integrated stereo feedback, analog-input, digital amplifier with a power stage designed to drive 2-Ω to 8-Ω speakers at up to 300 W per channel in stereo, or up to 600W bridged. This amplifier requires only a single 20V to 50V power supply to deliver high-quality, high-efficiency audio amplification. This amplifier is configured with two BTL channels or one PBTL channel and the possibility to apply either a standard single-ended or a balanced (differential) analog input signal. Since channels are BTL (bridge tied load) bus pumping is never an issue with these amplifiers. The input section of the amplifier has two OPA1632 opamps... very high-performance, fully differential, audio operational amplifier designed to operate with single-ended or differential input signals (balanced). Output section features our custom made high performance inductors and metallized polypropylen capacitors. This is a very high quality power amplifier, and as always, made with the state-of-the-art materials and impeccable workmanship Class D Audio is known for. Small Size - 5.25" X 3.75" (133.35mm X 95.25mm) Click & Pop Noise Reduction Short Circuit and Thermal Protection Two Speed 12V Fan Output (most conditions will not require a fan) Sync Input Stereo or Bridged Configuration House Keeping Power Supplies Built-In... only requires one 20V to 50V power Supply

Specifications:
Model TI-600
Number Of Channels 2
RMS Power Per Channel 8 Ohms 135W RMS X 2
RMS Power Per Channel 4 Ohms 270W RMS X 2
RMS Power in Bridge Mode Up to 600W X1
Input Sensitivity 2V
Total Harmonic Distortion (THD) .02%
Frequency Response 10hZ to 45KHz
Input Impedance RCA 30K
Input Impedance XLR 30K
Voltage Gain for RCA Input 30
Voltage Gain for XLR Input 30
Power Requirements 24 Volts DC to 48 Volts DC
Dimensions (W x H x D) Inches 3.75 X 1.5 X 5.25
Dimensions (W x H x D) Millimeters 95.3 X 38.1 X 133.4
Product Weight (lbs/kg) 1.5/ 0.7
Shipping Weight (lbs/kg) 2.0/ 0.9
Manufacturer Class D Audio

Product Reviews

Login or Register to write a review.
Reviewed by customer
08/15/2016 - 02:27:31 PM
Ideal battery powered amplifier
I'm using my amplifier on a solar 24V d.c. system, so at 3 watts idle power, 90% operational efficient plus 95db spl at 1 Watt efficient speakes draws next to no energy all day (compared with the old 200Watts at idle amp - 66 times reduction).
Sounds great using quality speaks and running into 6 ohm, heat sink hardly gets warm.
Only slight complaint is the speak cable connectors have no serrations to bight harder to reduce the risk of the heavy cables being pulled out (but they should be secured anyway).
Keep up the good work.
Australia
Reviewed by customer
08/15/2016 - 02:26:49 PM
Impressed
Amp complete - dual mono with two of the TI-600's. I can not believe the power these little boards put out. Have my VMPS tower II's jumpin! Amp is definitley brighter than my trusty Yamaha M2 - but then the M2 is is 28 years old... Anyway, I like the sound of these boards - they certainly reveal any flaw in the source material. I found myself dialing down the treble about 2 db on most sources. Cone control is solid right to the rail, then they lose it a little and the woofers start getting jiggy.. but it is freakin LOUD at that point, much louder than I would ever listen to for any length of time. and the fans, which I did hook up, never turned on. Sweet.
Reviewed by customer
08/15/2016 - 02:26:05 PM
Nice!
Bought two of these modules - building a dual-mono 600w / channel amp. Initial testing with a 25v / 5a power supply indicates that it wants MORE POWER!- even with class D, there is no free lunch... So I am presently building 50v supplies with 1000va torroids and 60,000uf.) Will give full review when amp is complete and extended listening has been done. But so far, so good, and Tom is the MAN!
Reviewed by customer
08/15/2016 - 02:25:35 PM
Amazing specs
This seems like manna from heaven for all the audiophile DIYers. Wish they had an office in India.
Reviewed by customer
08/15/2016 - 02:25:03 PM
excelent
super amplifier how can bay in romania?
Reviewed by customer
08/15/2016 - 02:24:26 PM
600W Class D Power Amplifier, Balanced Input, 2 Ohm
I LIKE THIS AMP OVER THE TRIPATH 4 CHANNEL BOARD, IT IS SMOOTH ,SMALL BOARD. AND ONLY NEEDS ONE POWER SUPPLY VOLTAGE.. THE SPECS SHOULD TELL THE REST. THE POWER SUPPLY I AM USING HAS NEVER KICKED ON THE COOLING FAN, THIS SHOULD GIVE YOU AN IDEA OF HOW EFFICENT THAT THE BOARD IS. LOW POWER CONSUMPTION UNDER HIGH WATTAGE. I ALSO LIKE THE LOW IMPEDANCE [2 OHM] SO I CAN CONNECT MY 6 OHM KLIPSCH SPEAKERS IN PARALELL GIVING ME 4 SPEAKERS OUTPUT AT 3 OHMS EACH CHANNEL!

Products You May Like