TI-300 Audio Power Amplifier Module

TI-300 Audio Power Amplifier Module
Click to enlarge
Price: $160.00
Product ID : TI-300 Module
Manufacturer: Class D Audio USA
E-mail to a friend | Add To Wish List

Purchase

Description

Made in the USA by Class D audio, this Class D Audio power amplifier is based on the Texas Instruments new TAS5615 digital amplifier chip. It's a high-performance, integrated stereo feedback, analog-input, digital amplifier with a power stage designed to drive 4-Ω to 8-Ω speakers at up to 160 W per channel in stereo, or up to 330W bridged. This amplifier requires only a 20V to 50V power supply to deliver high-quality, high-efficiency audio amplification. This amplifier is configured with two BTL channels or one PBTL channel and the possibility to apply either a single-ended or a differential (ballanced) analog input signal. The input section of the amplifier has two OPA1632 opamps... very high-performance, fully differential, audio operational amplifier designed to operate with single-ended or differential input signals. Output section features our custom made high performance inductors and metallized polypropylen capacitors. This is a very high quality power amplifier, and as always, made with the state-of-the-art materials and impeccable workmanship Class D Audio is known for.

Features: Small Size - 5.25" X 3.75" (133.35mm X 95.25mm) Click & Pop Noise Reduction Short Circuit and Thermal Protection Two Speed 12V Fan Output (most conditions will not require a fan) Sync Input Stereo or Bridged Configuration House Keeping Power Supplies Built-In... only requires one 24V to 48V power Supply Specification Output stage supply voltage 20 V – 50 V Number of channels 2 Load impedance 4 to 8 Ω Output power, 8 Ω, 160 W Dynamic range >100 dB(A) SE to differential amplifier OPA1632D Output stage TAS5615 Other features +15-V onboard switcher from PVDD supply Output power, 1% THD+N, BTL, 8 Ω: 140 W 1 kHz, TA = 25°C Output power, 10% THD+N, BTL, 8 Ω: 170 W 1 kHz, TA = 25°C Output power, 1% THD+N, PBTL, 4 Ω: 270 W 1 kHz, TA = 25°C Output power, 10% THD+N, PBTL, 4 Ω: 330 W 1 kHz, TA = 25°C Maximum peak current, BTL: >7 A 1-kHz burst, 1 Ω, ROC = 22 kΩ Maximum peak current, PBTL: >10 A 1-kHz burst, 1 Ω, ROC = 22 kΩ Output stage efficiency: >90% 2 x channels, 8 Ω Damping factor 27 1 kHz, relative to 8-Ω load H-bridge supply current: 50 mA 1 kHz, input grounded Idle power consumption: <3 w="" h-bridge="" supply="" input="" grounded="" audio="" performance="" thd="" n="" btl="" 8="" :="" 1="" 0="" 03="" khz="" 10="" 05="" 50="" 100="" 4="" dynamic="" range:="">100 dB Ref: rated power, A-weighted, AES17 filter, 2 ch avg Noise voltage: 320 μVrms A-weighted, AES17 filter Click/pop, DC step: <30 mv="" mute="" unmute="" no="" signal="" 4="" channel="" separation="" btl:="">89 dB 1 kHz Frequency response: ±0.5 dB 100 W / 8 Ω, unclipped

Specifications:
Model TI-300
Number Of Channels 2
RMS Power Per Channel 8 Ohms 80W RMS X 2
RMS Power Per Channel 4 Ohms 160W RMS X 2
RMS Power in Bridge Mode Up to 300W X1
Input Sensitivity 2V
Total Harmonic Distortion (THD) .02%
Frequency Response 10hZ to 45KHz
Input Impedance RCA 30K
Input Impedance XLR 30K
Voltage Gain for RCA Input 30
Voltage Gain for XLR Input 30
Power Requirements 24 Volts DC to 48 Volts DC
Dimensions (W x H x D) Inches 3.75 X 1.5 X 5.25
Dimensions (W x H x D) Millimeters 95.3 X 38.1 X 133.4
Product Weight (lbs/kg) 1.5/ 0.7
Shipping Weight (lbs/kg) 2.0/ 0.9
Manufacturer Class D Audio

Product Reviews

Login or Register to write a review.
Reviewed by customer
08/15/2016 - 02:28:34 PM
Clean Reliable Amplifier
Great way to see what Class D is all about. Have now had this amplifier long enough to see that it is reliable.

After going through 3 Asian built amps which all died prematurely, I decided to pony up a few more dollars and try this TI based amp.

Amp runs very cool even when played up a bit. Works well with the 24V Meanwell turned up to ~30V. Sounds good out of the box.

Products You May Like